Show ethernet cfm statistics symbols

images show ethernet cfm statistics symbols

Best-case one-way delay. The valid values of the timeout period range from 1 to Usage Guidelines To enable cross-checking after a device has booted up, you must issue the ethernet cfm mep crosscheck enable command. Optional Specifies a specific time at which to start the probe in hour notation. Usage Guidelines When using this command, if a domain name is not specified, information for all domains is shown. Displays information about maintenance points configured on a device.

  • show oam ethernet connectivityfaultmanagement delaystatistics TechLibrary Juniper Networks
  • show oam ethernet connectivityfaultmanagement mepstatistics TechLibrary Juniper Networks

  • Chapter: show ethernet cfm maintenance-points local through weight use the show ethernet cfm statistics command in privileged EXEC mode.

    images show ethernet cfm statistics symbols

    Specifies the total symbol period and the TLVs received for each frame. IP SLA integration with CFM gathers Ethernet layer statistical measurements by . Display current or aggregated operational status and statistics.

    . ethernet oam link-monitor symbol-period {threshold {high {high symbols. show ethernet cfm smep; show ethernet cfm statistics; show ethernet Configures an error symbol period on an Ethernet OAM interface.
    To display detailed information about Ethernet connectivity fault management CFM performance monitoring, use the show ethernet cfm pm command in privileged EXEC mode. To remove the configuration, use the no form of this command.

    show oam ethernet connectivityfaultmanagement delaystatistics TechLibrary Juniper Networks

    The following example shows how to configure putting the interface into the line-protocol-down state when a wiring-conflict event occurs. Indicates the result of comparing its local configuration and the remote configuration found in the received local information type length value TLV field. Cross-checking is disabled when you issue the command with the disable keyword.

    images show ethernet cfm statistics symbols

    images show ethernet cfm statistics symbols
    LOCATION MAISON SERIGNAN DU COMTAT 848
    Puts the line protocol into the down state for an interface when a capabilities-conflict event occurs.

    The value must be a divisor of the number of packets per probe. Creates a syslog entry when a critical-event notification is received. Optional Specifies the Ethernet interface on which to show the Ethernet loopback session. Performs an error-disable function on the interface. The table below describes the significant fields shown in output of the show ethernet lmi command using the evc and map keywords. The following example shows output from a show ethernet oam summary command:.

    show ethernet oam statistics .

    high and low must be specified) High threshold, in symbols, that causes a frame error event to trigger an action.

    show oam ethernet connectivityfaultmanagement mepstatistics TechLibrary Juniper Networks

    Review of Metro Ethernet technologies & Ethernet OAM . Statistics can be Ceasar#show ethernet oam summary. Symbols: * - Master Loopback State. MX Series,EX Series,ACX Series,T On MX Series routers with Ethernet interfaces on Dense Port Concentrators (DPCs), display ETH-DM delay statistics.
    Usage Guidelines Use this command to change the number of distribution statistics kept from the default 2 to the specified number.

    Performs no action on the interface when a remote-loopback event occurs.

    Forced switch. Optional Number of the interface.

    Video: Show ethernet cfm statistics symbols Dashboard Warning Lights Explained - Quick Tip

    Remote loopback is disabled by default. String of a maximum of characters in length. In the following example, operation 25 begins actively collecting data at p.

    images show ethernet cfm statistics symbols
    Yhs yorktown high school
    Displays information about a remote maintenance point domains or levels or details in the CFM database.

    Number of information elements IEs that are not in the correct sequence. The high keyword sets a high threshold for ingress frames received with CRC errors. Specifies the retransmission period.

    images show ethernet cfm statistics symbols

    To display Ethernet microwave event status information for one or more interfaces, use the show ethernet event microwave status command in privileged EXEC mode.

    5 comments

    5 thoughts on “Show ethernet cfm statistics symbols”

    1. The traceroute cache stores entries from previous traceroute operations. Indicates that there is no domain name.

    2. Optional Configures high and low thresholds for an error-symbol period that trigger an error-symbol period link event.

    3. The following example shows how to configure putting the interface into the line-protocol-down state when a connection timeout occurs.

    4. Optional Enter the instance keyword followed by the Ethernet ring instance number. Current configuration : bytes!