Rlc resonance lab report conclusion flame

images rlc resonance lab report conclusion flame

Of course, when working with quantities on the degree of micro and milli, it would be extremely difficult to figure out the resonance frequency. The next thing to do was monitor the output voltage on the oscilloscope screen and record the data. Since there is no way to measure the impedance directly using the probes, the graph took a little time to make—as Multisim is a very indepth software with many functions. In addition, the capacitive reactance is written as a negative reactance. Yujin Matsutoya. Typically made of carbon, each resistor is color coded so identification can be made easier. Kendrick Moreno.

  • Resonant Response of RLC Circuits
  • Lab Report 8 Electrical Network Resistor

  • Margaret Wettergreen PHY L 03/13/ Lab #8: RLC Resonance of this lab was to study series resonance in an RLC circuit (composed of a resistor. Conclusion: By observing the characteristics of a series RLC circuit, we were able.

    Resonant Response of RLC Circuits

    Conclusion This experiment introduced series and parallel RLC circuits. We learned how to find the resonant frequency of the circuit. We also found the. Lab Report 8 - Free download as PDF File .pdf), Text File .txt) or read series RLC circuit and to identify the resonant frequency and the.
    So the correct form of XC should be —j By plotting the output voltages and the frequency, we could also see the behavior of the circuit as different frequencies were applied.

    images rlc resonance lab report conclusion flame

    We set the function generator to exactly 1 V—however we got readings that ranged from 1 V — 1. A simulation circuit constructed using Multisim shows the exact same circuit with a function generator and oscilloscope attached in Fig. Notice how they are close to overlapping—but their difference represents the lag that occurs when a sinusoidal voltage is applied.

    images rlc resonance lab report conclusion flame

    images rlc resonance lab report conclusion flame
    Rlc resonance lab report conclusion flame
    In addition, the calibration of the oscilloscope and the function generator probably had a hand in it as well.

    After attaching the function generator to the input—we set it to create a 1 V peak to peak voltage and a 5 kHz sine wave. Frequency for Parallel RLC.

    Aniruddh Sharma. Matthew Fearrington.

    3: Series RLC Circuit plot of output voltage vs. frequency When A Multisim. For this lab experiment, we will establish the resonance frequency of series .

    Conclusion: RLC circuits have a commonplace usage among.

    Video: Rlc resonance lab report conclusion flame Series Resonance : R-L-C,Practical BEE

    Report any broken equipment or defective parts to the lab instructor. Do not open The danger of injury or death from electrical shock, fire, or explosion is present while conducting. Conclusion: This is your interpretation of the results of the experiment as an engineer.

    .

    images rlc resonance lab report conclusion flame

    Similar frequency exists for a parallel RLC circuit. The finer details of the Laboratory Report Format may vary from instructor to.

    Use caution when working with hot plates, steam generators, open flames, and the heat.

    Attach a typed Conclusion section and a Discussion section. If a μF capacitor and a MΩ resistor form a series RC circuit, what is the RC time.
    If we input frequencies, it is essentially possible to guess and check what the resonance frequency would be. If you wanted to work out the solutions again—you would use Eq.

    Like this document?

    Lab Report 8 Electrical Network Resistor

    Malith Madushan. The capacitor was not 0. Latif Nurohman Bayu Nugroho.

    images rlc resonance lab report conclusion flame
    Rlc resonance lab report conclusion flame
    Full Name Comment goes here.

    This occurs because the current in the circuit is at a maximum at this frequency.

    More From Matthew Fearrington. Embeds 0 No embeds. Known as Multisim, it is a well-known program used by technicians, engineers, and scientists around the globe.

    4 comments

    4 thoughts on “Rlc resonance lab report conclusion flame”

    1. Lab Report 8. Just as in Part I of the lab, we had to manipulate the expressions to get the output in the AC analysis tool.

    2. This is due to the fact that the inductor and capacitor act as an open circuit at resonance—making all the current go through the resistor.